Mayline Convert Rule to Above Board Attachmen Bedienungsanleitung PDF herunterladen (Seite 1)

Fig. 1

INSTRUCTIONS TO CONVERT RULE TO

ABOVE-BOARD ATTACHMENT

REF # QTY. DESCRIPTION PART No.

E7 4 #6 x 1/2" Screw X37*

E8 8 #6 X 1/4" Screw X44S*

E9 2 #6 x 1" Screw X14*

E10 3 Knob K22*

E11 2 Brake Shoe Assembly A2123*

E12 1 Cable Clamp B9*

NOTE: Please count and inspect all pieces before disposing of any carton or packing materials.

COMPONENTS:

REF.# QTY. DESCRIPTION PART No.

1 CALL~~ Cable Coil CALL~~

2 2 Pulley Housing F314

HARDWARE BAG (PART No. A2297)

*for individual item, order that part number

REF # QTY. DESCRIPTION PART No.

E1 1 R.H. Corner Plate Assembly A2294*

E2 1 L.H. Corner Plate Assembly A2295*

E3 2 Stedge Stop F330*

E4 2 Side Guide B1003*

E5 4 Ball bearing Pulley P14*

E6 2 Washer W42*

Washer (E6)

Knob (E10)

1. Remove present end plates and sliding bars from end of

straightedges. (See Fig. 1)

2. Insert the two Ball bearing Pulleys (E5) into holes located

per Fig. 2 With knurled portion of stud in hole, push down until

shoulder is tight against blade.

3. Repeat for other end of Straightedge.

4. Install Cable Assembly. Refer to section "Instructions for

Restringing Mayline Straightedge".

5. Attach straightedge to board. Refer to section " Assembly

Instructions for Mounting Straightedge".

Ball bearing

Pulley (E5)

NOTE: Brake Shoe (E11)

located under cable

#6 x 1/4"

Screw (E8)

Pulley

Housing (2)

Fig. 2

Knurl End

of Pulley

Tap

When ordering components, specific color and/or size information may be required.

Contact a Mayline Customer Service Representative. 1-800-822-8037

CATALOG No.

7301A

7301B

7301C

(1)

1 2 3 4

Inhaltsverzeichnis

Seite 1 - ABOVE-BOARD ATTACHMENT

Fig. 1INSTRUCTIONS TO CONVERT RULE TO ABOVE-BOARD ATTACHMENTREF # QTY. DESCRIPTION PART No. E7 4 #6 x 1/2" Scr

Seite 2 - MAYLINE STRAIGHTEDGE

INSTRUCTIONS FOR RESTRINGINGMAYLINE STRAIGHTEDGERingTerminal (2)NOTE: Please count and inspect all pieces before disposing of any carton or packin

Seite 3 - ASSEMBLY INSTRUCTIONS

1. Place straightedge in position on Worksurface. Install Knob (E10) and Washer (E6) on both ends of straightedge. Do not tighten at this time. (Se

Seite 4

12. Pull cable on RIGHT side of worksurface to remove slack from this portion. Tighten Stedge Clamp Screw (E9) at this time.13. Pull cable on LEFT

Kommentare zu diesen Handbüchern

Keine Kommentare

Mayline Convert Rule to Above Board Attachmen Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Mayline Convert Rule to Above Board Attachmen herunter. Mayline Convert Rule to Above Board Attachmen User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Mayline Convert Rule to Above Board Attachmen Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Mayline Convert Rule to Above Board Attachmen herunter. Mayline Convert Rule to Above Board Attachmen User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Mayline Convert Rule to Above Board Attachmen